Best Water Cooling Case for Enthusiast Gaming PC in 2024

A water-cooled PC not only looks great but it also provides much better cooling to your major components that include your CPU and Graphics Card (Water block ones). Also, if you are an enthusiast and into extreme overclocking then water cooling will allow you to overclock your CPU and GPU to much higher frequencies. There are generally two types of liquid cooling or water cooling, one is the custom loop water cooling where you build your own water cooling loop using pipes/tubes, pump, radiator, reservoir, coolant/water, and waterblock for CPU and Graphics Card. Another one is closed-loop liquid cooling where ready-made or pre-built AIO liquid coolers are available for direct use and you just have to mount the waterblock unit on the CPU and radiator on the case. AIO water coolers are sealed units and you cannot open them or change or top up the coolant. There are also AIO liquid-cooled graphics cards too but they are only available for high-end GPUs. The performance of a custom loop water cooling is generally better than AIO closed-loop liquid cooler. However, custom loop water cooling is more expensive compared to AIO liquid cooling and air cooling.

Building a custom water cooling loop is a tough and tedious task compared to AIO and Air CPU coolers. Custom loop water cooling requires more space especially when you are cooling your waterblock graphics card with it and using multiple radiators. Therefore, it is not possible to employ custom water cooling in any computer case. So, there are some special PC cases available that are designed for extreme and advanced water-cooling setups. A good Water Cooling case has enough space to accommodate multiple radiators (360mm or bigger), Reservoir, and Pump with ease. Also, it should have full window tempered glass panels so that you and others can get a clear and complete view of your beautiful water cooled computer system. So, here I am going to list down the best water cooling cases or liquid-cooled PC cases for setting up a high-end water cooling setup for your CPU and GPU.

Check out:

• Best Tempered Glass Cases for Gaming PC
• Best High Airflow PC Cases for Gaming 
• Best LAN Party Cases for eSports Gaming PC
• Best RGB Cases for Building a Fancy Gaming PC

Note: There are some high-end CPU Air Coolers available too that can provide you the similar cooling performance of good AIO liquid cooler. You can check them out from the link given below.

Must Read: Best CPU Air Coolers for Overclocking & Gaming

Best Water Cooling PC Cases with Tempered Glass

Here are the best water cooling computer cases for building high-end water-cooled PC for enthusiasts and for overclocking. These liquid cooling PC cases are suitable for both custom loop and AIO closed loop liquid cooling solutions, and all of them come with big tempered glass panels. Below mentioned liquid cooling PC cases are available in mid-tower, full-tower, cube, and super-tower form factors.

Fractal Design Define R6 Black TG

If you are looking for a sturdy mid-tower water cooled PC case then you won’t find anything as good as the Fractal Design Define R6 Black TG. This is a classy looking, well-built, and very spacious computer case that can swallow all of your gaming components and water cooling loop comfortably. This mid-tower case can support up to eATX (up to 285mm) motherboards. The case has great airflow with plenty of fan mount points (nine fan mount points) and it comes with three Dynamic X2 GP-14 140mm fans pre-installed. The front panel of the case is made of brushed aluminum and on the top of the front case, you will find two USB 2.0 and USB 3.0 ports and audio ports. It features Third generation ModuVent technology that gives users the choice between a soundproof steel cover or a filtered multi-fan ventilation setup in the top panel. Also, you don’t have to worry about your storage needs as the case supports up to 8 drive bays for your hard drives and SSDs.

This mid-tower water cooling case is big enough to support high-end graphics cards up to 440mm in length, 185mm tall CPU coolers, and up to 300mm PSU. For water cooling, it supports up to 420mm radiator on top, 360mm in the front, and 280mm on the base. The case features two different layouts; the standard layout is designed for maximum storage capacity and the open layout is for water cooling setup. The left side panel has tempered glass and the right one is fitted to sound dampening material for minimizing noise.

Side panels on this case can be easily removed using the tool-less push locks. Other features include a Vertical 2.5 slot GPU mount, Dust filters, PWM Fan Hub, cable routing, and tool-free drive installation. The case is compatible with the Fractal Design Connect D1 USB 3.1 Gen 2 Type-C Upgrade Kit which you can buy separately. Overall, it is a modular, quieter, and elegant-looking water cooling case that is loaded with features and has solid build quality. Highly Recommended by me.

Check out: Best Silent Cases for Building a Quiet PC for HTPC, Gaming & Work

Fractal Design Define R6 Black TG Specifications
Form Factor	Mid-Tower
Motherboard	ITX, Micro-ATX, ATX, eATX (up to 285mm wide),
Drive Bays	3.5″/2.5″ x 6, 2.5” x 2 (hidden)
Front Ports	2 x USB 3.0, 2 x USB 2.0, Audio
Expansion Slots	7 + 2 vertical
CPU Cooler Height	185mm
Graphics Card Length	440mm
Radiator support	Front: 120/240/360 mm or 140/280 mm Top:       Standard layout – 120/240/360 mm (max 35 mm motherboard component height) Open layout – 120/240/360 mm – 140/280/420 mm (max 35 mm motherboard component height) Rear: 120mm Bottom: 120/240 mm or 140 / 280 mm
Fans & Cooling	Front: 3 x 120 mm or 2 x 140 mm, Top:       Standard layout: 3 x 120 or 2 x 140 Open layout: 3 x 120/140 mm Rear: 1 x 120/140 mm Bottom: 2 x 120/140 mm
Tempered Glass Panels	Side Panel (tinted)
Features	Tool-less push-to-lock for Side Panels, Tool-less Drive Installation, Dust Filters on Front, Top & Base, Sound Dampening Material on Right Side Panel, Standard and Open Layout, 300mm PSU support, Cable routing, ModuVent technology, PWM Fan Hub, Reversible front door

Buy Fractal Design Define R6 Black TG

Lian Li PC-O11 Dynamic Tempered Glass Case

[Compact yet Spacious, Dual PSU support, Great Build]

Lian Li PC-O11 Dynamic is a remarkable and one of the best cases for water cooling. This case has been developed with the help of DER8AUER, who is a world-famous overclocker from Germany. This is a mid-tower case that is compact, but packs a great amount of space and can accommodate up to E-ATX sized motherboards and dual PSUs. It has a boxy shape but it looks very classy and has got tempered glass panels on the front and sides that showcases every component inside it. This is a dual-chamber case and has got good airflow and can support a decent number of 120mm / 140mm fans on top, side, and at the bottom. On the front panel, you will find I/O ports that include two USB 3.0, one USB 3.1 Type-C, and HD Audio ports.

The case has great build quality and is quite sturdy because it is constructed from 0.8mm thick SECC steel. It can support high-end Graphics Cards up to 420mm in length and CPU Coolers up to 155mm in length. For water cooling, it can support up to three 360mm Radiators without interference, which is just amazing. Also, it has got complete protection from dust as it comes with four magnetic dust filters at the bottom, top and side panels. The case can support up to six SSDs and three HDDs for all your storage needs. Other features include Double Layer Cable Management Design and tool-less drive installation. So, if you are an enthusiast and are looking for a superior water-cooling case that is not bulky then you should definitely go for it. The case is available in two colors: black and white. Highly Recommended by me.  

Lian Li PC-O11 Dynamic Mid-Tower Case Specifications
Form Factor	Mid-Tower
Motherboard	Mini-ITX, Micro-ATX, ATX, E-ATX
Drive Bays	3.5” x 2, 2.5” x 4
Front Ports	USB 3.0 x 2, USB 3.1 Type-C x 1, HD Audio
Expansion Slots	8
CPU Cooler Height	155mm
Graphics Card Length	420mm
Radiator Support	360mm, 280mm, 240mm (x 3)
Fans & Cooling	Top: 120mm x 3 / 140mm x 2 Side: 120mm x 3 Bottom: 120mm x 3
Tempered Glass Panels	Front and Side
Features	Dual PSU support, 0.8mm SECC Sturdy Build Construction, 4 x Dust Filters (Top, Bottom, Side Panels), Double Layer Cable Management Design, Up to three 360mm Radiators support simultaneously without interference, Patented Designed Glass Mounting Mechanism

Buy Lian Li PC-O11 Dynamic Mid-Tower Case

Thermaltake Core P5 Tempered Glass Edition ATX Wall-Mount Case

If you want to showcase all of your fancy gaming components and water cooling loop then this open frame panoramic viewing case is a perfect choice. This is a beautiful ATX mid-tower case that has got a full-length tempered glass windowed panel on top, side, and top and you can literally see each and every component of your gaming rig from outside. You can easily set up a custom water loop with a reservoir in this case for your CPU and GPU. It supports up to 480mm radiators and is Thermaltake Tt LCS Certified. This is a modular case and supports 3-way placement layouts (Wall mount, Horizontal, and Vertical) and dual GPU layout locations (horizontal/vertical). The case does support 120mm / 140mm fan mount points on the left but you won’t be able to use them with the liquid cooling setup because the same location is shared for the radiator too. On the front panel of the case, you will find two USB 3.0 ports, two USB 2.0 ports, and Audio ports.

The case can support graphics cards up to 570mm (without Reservoir) and 280mm (with Reservoir) in length, CPU coolers up to 180mm tall, and PSU up to 200mm in length. The case is only good for a single radiator water cooling setup and you cannot use dual radiators or dual loop water cooling with it. A standard riser cable is included with this case for the vertical mounting of the graphics card. This case is a work of art and if you are looking for a case that provides a stunning look of your gaming components with RGB lighting then you should definitely get this one. It is also available in other colors that include red and snow (white). You can check them all by going to the link given below.

Thermaltake Core P5 Tempered Glass Edition Case Specifications
Form Factor	Mid-Tower
Motherboard	Mini-ITX, Micro-ATX, ATX
Drive Bays	1 x 3.5’’ or 2.5’’ (HDD tray), 3 x 3.5’’ or 2.5’’ (Hidden Behind the M/B tray)
Front Ports	USB 3.0 x 2, USB 2.0 x 2, HD Audio x 1
Expansion Slots	8
CPU Cooler Height	180mm
Graphics Card Length	280mm (with Reservoir), 570mm (without Reservoir)
Radiator support	Left Side: 1 x 480mm / 1 x 420mm
Fans & Cooling	Left Side: 4 x 120mm / 3 x 140mm
Tempered Glass Panels	Side, Top, Front (5mm)
Features	3-way placement layouts (Wall mount, Horizontal and Vertical), 200mm PSU support, DMD – Dismantlable Modular Design, Tt LCS Certified

Thermaltake Core P5 Tempered Glass Edition ATX Case

Phanteks Enthoo Luxe Tempered Glass Full Tower Case

Phanteks Enthoo Luxe Tempered Glass is a traditional and classy looking Full Tower case from Phanteks. This is a multipurpose case that can be used for building a water-cooled gaming PC and a traditional powerful desktop with lots of drives. It is an RGB PC case and comes with RGB LED strips on its front and top corners on both sides. The case offers plenty of drive bays and also comes with 5.25” bays which you can use for fitting an optical drive or a 5.25” fan controller. The case is very spacious with great airflow and comes with sufficient fan mount points on the front, rear, and top. On the front panel, you will find two USB 3.0, two USB 2.0, an LED switch, and Audio ports hidden in the hinged door.

The case supports 347mm long graphics cards, 193mm tall CPU coolers, and 318mm long PSU. For water cooling, it comes with Reservoir mounts, a Pump bracket and supports up to 420mm radiator on top, 250mm on the front, 120mm at the rear, and up to 240mm at the bottom. RGB LED lighting and effects, in this case, can be controlled using the LED switch and by RGB LED software that include MSI Mystic Light Sync, Asus Aura Sync, and Gigabyte RGB Fusion. The case is compatible with Phanteks RGB LED Strips. Other features include Dust Filter on Front and Top, Cable management, 3-pin Fan Hub (support 6 Fans), and Tool-free drive installation. Overall, a very practical case if you want a clean-looking case with lots of space, water cooling support, good build quality, and fancy RGB LED lighting.

Phanteks Enthoo Luxe Tempered Glass Case Specifications
Form Factor	Full Tower
Motherboard	ATX, EATX, uATX, mini ITX, SSI EEB
Drive Bays	5.25″ x 3, 3.5″ / 2.5″ x 6, 2.5″ x 4 (2 included)
Front Ports	2x USB 3.0, 2x USB 2.0, Mic, Headphone
Expansion Slots	7
CPU Cooler Height	193mm
Graphics Card Length	347mm
Radiator support	Front: up to 240mm Top: up to 360mm / up to 420mm Rear: 120mm Bottom: up to 240mm / 140mm
Fans & Cooling	Front: 120mm x 2 / 140mm x 2 Top: 120mm x 3, 140mm x 2 Rear: 120mm / 140mm x 1
Tempered Glass Panels	Side
Features	RGB LED lighting on Corners, Dust filters, Cable Management, Tools Free Drive Installation, Reservoir Mounts and Pump Bracket, Compatible with Phanteks RGB LED Strips and RGB motherboards, Sand-blasted Aluminum panels, Fan Hub (x6 fans)

Buy Phanteks Enthoo Luxe Tempered Glass Case

Corsair Obsidian Series 500D Premium Mid-Tower Case

Corsair Obsidian Series 500D is a modern, stylish and sleek mid-tower case that supports up to ATX sized motherboards. This is a beautiful case with smoked tempered glass doors on both sides. These are swing door panels that allow easy accessibility to your components. The case is pretty spacious and has got fan mount points at the front, top, and rear for achieving high airflow. The case looks very premium with its aluminum front panel and top plate. The top of the front panel consists of two USB 3.0 ports, USB 3.1 Type-C port, and audio. I think this is the only case in its segment to feature a front USB Type-C port.

The case can support graphics cards up to 370mm long, 170mm tall CPU coolers, and 225mm PSU. You can easily set up a dual radiator water cooling loop in this case as it supports up to 360mm radiator on front, and up to 280mm / 240mm radiator on top. It also includes a decent amount of drive bays for your SSDs and HDDs. Other features include removable dust filters, removable fan and radiator trays, cable routing, and tool-free drive installation. So, if you are looking for a relatively compact case for your water-cooled PC build then you cannot ignore this beauty with its Iconic Obsidian design.  

Corsair Obsidian Series 500D Mid-Tower Case Specifications
Form Factor	Mid-Tower
Motherboard	Mini-ITX, Micro-ATX, ATX
Drive Bays	3.5” x 2, 2.5” x 3
Front Ports	USB 3.0 x 2, USB 3.1 Type-C, Audio
Expansion Slots	7
CPU Cooler Height	170mm
Graphics Card Length	370mm
Radiator support	Front: up to 360mm Top: up to 280mm / 240mm Rear: 120mm
Fans & Cooling	Front: 120mm x 3 / 140mm x 2 Top: 120 x 2 / 140mm x 2 Rear: 120mm x 1
Tempered Glass Panels	Both Sides (smoked tempered glass)
Features	Aluminum Front and Roof Plate, 225mmPSU support, Swing Door Handles, Removable Fan and Radiator Trays, Cable routing, Removable built-in Dust Filters, Direct Airflow Path design

Buy Corsair Obsidian Series 500D Mid-Tower Case

Thermaltake Level 20 XT Cube Case

Thermaltake Level 20 XT is one of the newest cases in the Thermaltake Level 20 new case series. This is an E-ATX Cube Case and offers tons of space for a custom water cooling loop and other high-end gaming components. This cube gaming case is a looker and it comes with 4mm tempered glass panels on all its sides i.e. front, top, left, and right so that you can showcase all of your high-end gaming components in style. It has got plenty of fan installation mount points all around and can even support two 200mm fans at the front. This is a modular case and has a dual-chamber design where the lower chamber is for PSU and storage devices while the upper chamber houses PCI-E cards, motherboard, and graphics card. On the top of the front panel, you will get two USB 3.0 ports, two USB 2.0 ports, one USB Type-C port, and Audio ports.

The case supports high-end graphics cards up to 400mm long, 250mm tall CPU coolers, and a standard 220mm PSU. This is an ultimate case for water cooling as it is capable of supporting two radiators (up to 480mm / 420mm) on top and can support big radiators on the front, side, and bottom. You can easily set up an advanced custom water cooling loop with big radiators and reservoirs in this case. Other features include a dust filter, tool-free drive installation, and cable routing. Overall, it is one of the best-looking and spacious cube cases for building an enthusiast gaming PC with water cooling.                               

Thermaltake Level 20 XT Cube Case Specifications
Form Factor	E-ATX Cube Case
Motherboard	Mini-ITX, Micro-ATX, ATX, E-ATX
Drive Bays	6 x 3.5’’ or 2.5’’ (HDD Cage), 1 x 3.5’’, 2 x 2.5’’ (M/B Tray Hidden)
Front Ports	USB 2.0 x2, USB 3.0 x2, HD Audio x 1, Type-C x1
Expansion Slots	8
CPU Cooler Height	250mm
Graphics Card Length	400mm (with ODD cage), 590mm (without ODD cage)
Radiator support	Front: up to 360mm / 280mm (x1) Top: up to 480mm / 420mm (x2) Rear: 120mm / 140mm (x1) Left / Right: up to 480mm / 420mm (x1) Bottom: up to 480mm / 420mm (x1)
Fans & Cooling	Front: 3 x 120mm, 2 x 140mm, 2 x 200mm Top: 8 x 120mm, 6 x 140mm, 2 x 200mm Rear: 2 x 120mm or 2 x 140mm Bottom: 3 x 120mm Left / Right Side: 4 x 120mm, 3 x 140mm
Tempered Glass Panels	4mm Tempered Glass x 4(Left & Right & Front & Top)
Features	Tt LCS Certified, Chamber Design, 220mm PSU support, DMD: Dismantlable Modular Design, Cable routing, Tool-less drive installation

Buy Thermaltake Level 20 XT Cube Case

Corsair Obsidian Series 1000D Super-Tower Case

Corsair Obsidian Series 1000D is the bigger version of the Corsair Obsidian Series 500D mid-tower case that I have mentioned above in this post. This is a monstrous super tower case and can support up to SSI-EEB and E-ATX motherboards. It is a modern-looking and stylish case and has got tempered glass swingable doors on both sides for easy access to your components. It packs an enormous amount of space and can swallow all your big water cooling radiators and high-end gaming components without any hitch. The case has great ventilation and has 18 fan mounts for adding fans and increasing airflow. It has got telescopic tool-less modular radiator trays that can slide in and out for easy installation of fans and radiators. The top of the front case is RGB LED-lit and it contains four USB 3.0 ports, USB 3.1 Gen-2 Type-C port, a power button, and audio ports. The case includes a built-in CORSAIR Commander PRO fan and lighting controller that comes with 6 fan connectors and two RGB connectors for Corsair RGB lighting devices. You can control the RGB lighting and fan speed using Corsair iCUE or Link software.

This is a dual system ready case that can run two systems concurrently with E-ATX and mini-ITX motherboards having separate PSUs. This can prove very handy when you want to build one system for gaming purposes and another one for online streaming to twitch so that neither of them will suffer performance breakdowns due to different tasks. The case is also capable of supporting up to 11 storage drives (2.5” / 3.5”).

It supports high-end graphics cards up to 400mm in length and 180mm tall CPU coolers. This case is perfect for building an advanced dual water cooling loop with multiple radiators as it can support dual 480mm radiators at the front, a single 420mm radiator on top, and up to 240mm radiator at the rear. Other features include cable routing, dust filters, and tool-less drive installation. The build quality of the case is top-notch and if you are an enthusiast who is looking for a big, powerful, feature-rich, modern stylish case for extreme build then this one is for you.   

Corsair Obsidian Series 1000D Super-Tower Case Specifications
Form Factor	Super Tower
Motherboard	Mini-ITX, Micro-ATX, ATX, E-ATX, SSI-EEB
Drive Bays	3.5” x 5, 2.5” x 6
Front Ports	USB 3.0 x 4, USB 3.1 Gen-2 Type-C x 2, Audio
Expansion Slots	8
CPU Cooler Height	180mm
Graphics Card Length	400mm
Radiator support	Front: up to 480mm (x2) Top: up to 420mm (x1) Rear: up to 240mm / 140mm (x1)
Fans & Cooling	Front: 8 x 120mm Rear: 2 x 120mm / 140mm Top: 3 x 140mm
Tempered Glass Panels	Both Sides (Smoked Tempered Glass Doors)
Features	Side Tempered Glass Doors, CORSAIR Commander PRO Fan and Lighting controller, RGB LED-lit front panel, standard or vertical GPU mounting, pump and reservoir fit points, tool-less modular radiator mounting trays, cable routing, tool-less drive installation, Corsair iCUE software support, Dual system ready

Buy Corsair Obsidian Series 1000D Super-Tower Case

Thermaltake Tower 900 E-ATX Vertical Super Tower Case

This case is a piece of art and is designed in collaboration with Watermod France. It is a vertical super-tower case and supports up to E-ATX sized motherboards. The case comes with 5mm tempered glass panels on top and sides and you can view each and every component clearly in this case. It is a huge case and offers tons of space for the biggest of the gaming components you can find. For cooling, it has plenty of fan mount points at the sides, top, and rear. The front panel comes with I/O ports that include four USB 3.0 ports and HD audio ports.

It can fit a 400mm long high-end graphics card, 260mm tall CPU coolers, and 220mm PSU. For water cooling, it supports 480mm and 560mm radiators and has two reservoir mounts. The case is highly modular and you can customize it according to your needs. Other features include tool-free drive installation and cable routing. So, if you are looking for a beautifully crafted case with lots of space and large tempered glass windows then look no further. It is available in two colors; black and snow white.

Thermaltake Tower 900 E-ATX Vertical Case Specifications
Form Factor	Super Tower
Motherboard	Mini-ITX, Micro-ATX, ATX, E-ATX
Drive Bays	5.25” x 1, 6 x 3.5’’ or 2.5’’ (With HDD Cage), 2 x 2.5’’ (With HDD tray)
Front Ports	USB 3.0 x 4, HD Audio x 1
Expansion Slots	8
CPU Cooler Height	260mm
Graphics Card Length	400mm
Radiator support	Left / Right Side: 1 x 480mm, 1 x 560mm
Fans & Cooling	Left Side: 4 x 120mm, 4 x 140mm Right Side: 4 x 120mm, 4 x 140mm Top: 2 x 120mm, 2 x 140mm Rear: 2 x 120mm, 2 x 140mm HDD Cage: 1 x 120mm, 1 x 140mm
Tempered Glass Panels	Front and Both Sides (5mm thickness)
Features	220mm PSU support, Tt LCS Certified, DMD – Dismantlable Modular Design, Tool-free drive installation and cable routing.

Thermaltake Tower 900 E-ATX Vertical Super Tower Case

Thermaltake View 71 Tempered Glass Edition Full Tower Case

Thermaltake View 71 is a Full Tower case in the View case series that is focused to provide you with a complete view of your components from the outside. The case comes with swing-open full window tempered glass panels on the sides for easy access and a tempered glass panel on top and front. This is a stunning-looking case and for cooling, it comes pre-installed with a 140mm Riing LED Blue fan at the rear and front. You can optionally install more fans at the front, top, and bottom if you want to increase the airflow further. The front panel includes two USB 3.0 ports, two USB 2.0 ports, and audio ports.

The case can accommodate up to 410mm long graphics card (without HDD rack), 190mm tall CPU coolers, and up to 420mm radiators on the front, top, and side. In this case, you can also mount your graphics card vertically using the integrated Riser GPU bracket. The case features a modular design and is suitable for building a high-end gaming PC for 4K gaming. Other features include cable routing, tool-free drive installation, and a fan filter on top. This case is also available in the RGB edition and you can check both of them out from the links given below.

Thermaltake View 71 Tempered Glass Edition Case Specifications
Form Factor	Full Tower
Motherboard	Mini-ITX, Micro-ATX, ATX, E-ATX
Drive Bays	2.5” x 4 or 3.5”x4(HDD Rack), 2.5”x 6 or 3.5” x 3 (Hidden)
Front Ports	USB 3.0 x 2, USB 2.0 x 2, HD Audio
Expansion Slots	8+2
CPU Cooler Height	190mm
Graphics Card Length	310mm (With HDD Rack), 410mm (Without HDD Rack
Radiator support	Front: 1 x 360mm, 1 x 420mm Top: 1 x 360mm, 1 x 420mm Rear: 1 x 120mm, 1 x 140mm Right: 1 x 360mm, 1 x 420mm Bottom: 1 x 240mm
Fans & Cooling	Front: 3 x 120mm, 2 x 140mm Top: 3 x 120mm, 3 x 140mm Rear: 1 x 120mm, 1 x 140mm Bottom: 2 x 120mm
Tempered Glass Panels	(Left & Right & Front & Top) 5mm Tempered Glass x 4
Features	Tt LCS Certified, 220mm PSU support, Modular Design, Tool-Free installation, Cable routing, Riser GPU Support Bracket for Vertical GPU mounting

Buy Thermaltake View 71 Tempered Glass Full Tower Case

Buy Thermaltake View 71 Tempered Glass RGB Full Tower Case

See also:

• Best Inverted PC Cases [ATX & Micro-ATX]
• Best Test Bench for Hardware Testing and Benchmarking

Final Words

In the end, I would like to say that if you are looking forward to building a PC with water cooling then selecting the right case is very important. This is due to the fact that not every case is designed for water cooling and the ones that support it may not be suitable for bigger and advanced water cooling loop. Here I have listed the best water cooling cases for all popular form factors and they fully support custom water cooling loop and AIO liquid coolers. You can select the right one according to your requirements or needs and if you have any doubts or queries regarding them then please ask me by leaving a comment below.